色老板在线精品免费视频

<optgroup id="bncdy"></optgroup>
<samp id="bncdy"><center id="bncdy"><xmp id="bncdy">
<ruby id="bncdy"><i id="bncdy"></i></ruby>

        <strong id="bncdy"></strong>
        <acronym id="bncdy"><sup id="bncdy"><nav id="bncdy"></nav></sup></acronym>

        Shenzhen Grande Electronic Linkedin Page
        Shenzhen Grande Electronic Co., Ltd logo
        E-mail us for a Quote:
        sales88@greattong.com
        Call us now:
        +86-755-83261869

        Technical Article


        PCB Fabrication: Different Techniques for Plating

        Time:2017-04-20 10:02:24 Click:

        The hole-wall will obtain electro-less copper as well as about 0.025 mm (0.001 inch) of electroplated copper on through-hole PCBs that are plated. External lines will obtain about 0.025 mm (0.001 inch) of copper plating, using copper electroplating methodology, on top of the initial 0.5 or 1.0 ounces of copper foil that already exists. 

        Depending on the requirements that must be adhered before or after the solder mask, all bare circuit elements must be protected by the following approved list of finishes:
        ? Immersion Silver
        ? Usual coating thickness: 0.20 μm (0.00007 in) to 0.50 μm (0.0002 in)
        ? Superior ability for soldering
        ? Superior surface coplanarity
        ? Superior way to obtain uniform hole sizes
        ? Good for using in fine-pitch part technology
        ? Good for surface contrast – assembly vision ability
        ? PCB is not subjected to thermal shock (as with HASL)
        ? Good for “Pb Free” soldering

        Nickel: Hard Gold
        ? Usual thickness: 0.7 μm (0.00003”) to 1.3 μm (0.00005”) gold (99.7%) over 5.0
        ? μm (0.0002”) nickel or 0.2 μm (0.000008”) to 0.3 μm (0.00001”) gold (99.7%) over
        ? 5.0 μm (0.0002”) nickel for a solderable surface
        ? Very good for corrosion resistance
        ? Rated at 130-220 Knoop hardness
        ? Very good wear resistance
        ? Excellent for surface rotary switches, on-off contacts, and edge connectors
        ? Very good shelf life

        Nickel: Soft Gold
        ? Usual thickness: 0.7 μm (0.00003 in) to 1.3 μm (0.00005 in) gold (99.9 percent) over 5.0
        ? μm (0.0002 in) nickel
        ? Very good corrosion resistance
        ? Below 90 Knoop hardness
        ? Well suited for pressure contacts and aluminum or gold-wire bonding
        ? Average wear resistance
        ? Very good shelf life

        Electroless Nickel or Immersion Gold (99.9 percent Gold)
        ? Usual thickness is 0.08 μm or 0.000003 inch to 0.2 μm or 0.000008 inch gold over 0.5 μm or 0.0002 inch nickel
        ? Superior resistance from corrosion
        ? Adequate for aluminum wire bonding
        ? Very Good for the use of fine pitch technology
        ? Superior ability for soldering
        ? Very good shelf life

        HASL (Eutectic; 63 percent Tin to 37 percent Pb
        ? Usual coating thickness is 0.8 μm (0.000003 in) to 5 μm (0.0002 in); dependent upon the design
        ? Very good ability for soldering
        ? 0.635 mm (0.025 in) surface mount pitch or greater ability
        ? 0.75mm (0.030 in) is the minimum board thickness ability
        ? Adequate shelf life

        Anti-Tarnish / Preservative for Organic Solder-ability
        ? Usual coating thickness: 0.2 μm (0.000008 in) – 0.5 μm (0.0002 in)
        ? Good ability for soldering
        ? Very well suited for surface coplanarity and uniformity of the size of the hole
        ? Very good for fine-pitch technology
        ? Better surface contrast – capability for assembly vision
        ? PCB does not experience thermal shock (as with HASL)
        ? Adequate shelf life (1 year)

        Matte Tin (Nickel)
        ? Usual thickness is 7.6 μm (0.0003 in) Tin above 12.7 μm (0.0005 in) of nickel
        ? Surface can be soldered
        ? Adequate life on shelf

        Previous:DFM Validation for PCB Assembly

        Next:PCB Fabrication: Dimensions of the Drill’s Highest and Lowest Diameter


        Request an Official Quote

        Questions

        E-MAIL

        File Upload

        Upload a list of files

          Please upload your Gerber files and BOM. You can upload an unlimited number of files as long as the total size of all files does not exceed 20 MB. To ensure you receive your official quote in less than 24 hours, please include the quantity of circuit boards for which you would like a quote.

          If you require that we sign a Non-Disclosure Agreement (NDA), please send it to us prior to sending your files and we will be happy to accommodate.

           
          Home About Us Services Quality Pb-Free News Contact Us


          Copyright ® 2017,Shenzhen Grande Electronic Co., Ltd. All Rights Reserved. 中文站 Sitemap

          色老板在线精品免费视频

          <optgroup id="bncdy"></optgroup>
          <samp id="bncdy"><center id="bncdy"><xmp id="bncdy">
          <ruby id="bncdy"><i id="bncdy"></i></ruby>

              <strong id="bncdy"></strong>
              <acronym id="bncdy"><sup id="bncdy"><nav id="bncdy"></nav></sup></acronym>